Page 1 of 1

STICKY: Unsupported Devices that work list

Posted: Tue Feb 03, 2015 10:35 am
by Middyeasy
FInd here a list of devices that have been reported to have worked with the rooted Wink Hub by category:

-Motion Senors
1. PEQ motion Sensor Zigbee
2. Ecolink Z-Wave PIR (PIRZWAVE2-ECO)



to report a new device that you have discovered works with the hub just post below and we will add it.. please also post any tech notes or attributes or helpful info about your experience with it.

EcoLink Z_Wave PIR motion sensor

Posted: Tue Feb 03, 2015 10:36 am
by Middyeasy
I haven't tried it myself but two users over at reddit claim that It works fine..


http://www.reddit.com/r/winkhub/comment ... et_immune/

Re: STICKY: Unsupported Devices that work list

Posted: Fri Apr 08, 2016 9:55 pm
by hangflyer
Swann One make a Zigbee Smart Plug for Australia. It can be turned on and off via Zigbee. It runs on 240v and supports up to 2400W.

[root@flex-dvt ~]# aprontest -m1 -l
Gang ID: 0x0015f44d
Manufacturer ID: 0x109f, Product Number: 0xff08
Device has 18 attributes...
swanplug
ATTRIBUTE | DESCRIPTION | TYPE | MODE | GET | SET
61440 | ZCLVersion | UINT8 | R | 3 |
61441 | ApplicationVersion | UINT8 | R | 34 |
61442 | StackVersion | UINT8 | R | 53 |
61443 | HWVersion | UINT8 | R | 12 |
61444 | ManufacturerName | STRING | R | netvox |
258048 | IdentifyTime | UINT16 | R/W | 0 |
4 | NameSupport | UINT8 | R | 128 |
1 | On_Off | STRING | R/W | ON | ON
117633024 | ZB_CurrentSummationDelivered | UINT64 | R | 0 |
117633536 | ZB_Status | UINT8 | R | 0 |
117633792 | ZB_UnitOfMeasure | UINT8 | R | 0 |
117633793 | ZB_Multiplier | UINT32 | R | 1 |
117633794 | ZB_Divisor | UINT32 | R | 1000 |
61445 | ModelIdentifier | STRING | R | Z809AE3R |
61446 | DateCode | STRING | R | 20141120 |
61447 | PowerSource | UINT8 | R | 1 |
117633795 | ZB_SummationFormatting | UINT8 | R | 251 |
117633798 | ZB_MeteringDeviceType | UINT8 | R | 0 |

[root@flex-dvt ~]# aprontest -m1 -t1 -u -v ON
Update device with master ID 1, setting value ON for attribute 1
Waiting for 1 callbacks...
Received a myNodeDataCallback from Zigbee
Source: aprontest
Event: RADIO_EVT_NODE_UPDATE
Status: FLX_OK
Node: 1
[root@flex-dvt ~]# aprontest -m1 -t1 -u -v OFF
Update device with master ID 1, setting value OFF for attribute 1
Waiting for 1 callbacks...
Received a myNodeDataCallback from Zigbee
Source: aprontest
Event: RADIO_EVT_NODE_UPDATE
Status: FLX_OK
Node: 1

It also does energy monitoring, but I have not yet figured out how to access this with aprontest.

I just got my Wink yesterday and it was running the latest firmware. I was able to get into the bootloader and then root it using the nand short trick.
I'm planning to get a web server running on it and create a simple php based system for controlling local devices.